Platinum PRO Plug-in Nissan Z32 Fairlady 300ZX Kit

13.282,50 DKK  m/Moms
( 10.626,00 DKK  u/Moms )
SUITS: Nissan Z32 Fairlady 300ZX. Manual transmission only.
INCLUDES: Platinum PRO Direct Plug-in ECU, Plug and pins for auxiliary I/O harness. Haltech CAN adaptor cable DTM-4 female receptacle/socket to 8 pin black Tyco 3"/75mm (used to adapt a Platinum series ECU to a DTM-4 Elite CAN system), USB programming cable and USB Software Key.
NOTES: Directly accepts an input from a flex fuel sensor.
Model/varenr.: HT-055107
Lager: Leveringstid er 1-2 uger, hvis udsolgt. dag(e)
If you are after a simple plug-and-play option and your car still has its original engine and wiring in it, a Plug-in ECU is the easiest and quickest solution. You simply unplug the factory ECU, and plug the Haltech ECU directly into the factory harness. Load your base map and you're ready to go!

Features:
• Direct plug and play replacement of the OEM ECU, no re-wiring necessary.
• Uses the cars factory sensors
• Supports Sequential Injection (peak and hold) and Direct fire ignition
• Windows 2000, XP, Vista, Windows 7 compatible software
• Real time programming, instant hesitation free adjustment while engine is running
• Fully user definable 32 x 32 mapping
• Tuning via Volumetric Efficiency (VE), Injection time or Lambda Correction (MAF)
• Diagnostic trouble code storing & Check engine light control(Access through laptop only )
• Selectable onboard internal MAP sensor rated to 150kPa (up to 1.5 Bar or 22psi boost)
• Wideband “auto tuning” using user definable target AFR table
• USB and CAN Communication Port

Supported Oem Functionality:

• Boost Control
• A/C Output
• Idle Control
• Thermofan 1&2
• Check Engine Light
• Fuel Pump Control Module
• MAF Sensor
• Narrowband Sensors
• Vehicle Speed
• Fuel temperature Sensor

Factory Outputs:
• 6 x Fuel Injector outputs
• 6 x Ignition outputs
• N-VCT (Nissan Variable CAM Timing Control)
• Tacho, Boost Control,  AC Clutch Relay,  Idle Control
• Thermo Fan,  Check Engine Light,  Fuel Pump (Variable Speed)

Factory Inputs:
• MAF sensors,  Throttle Position Sensor, Oxygen sensors,
• Coolant Temperature sensor, Vehicle Speed Sensor,
• Fuel Temperature sensor, Knock Detection Sensor

Expansion I/O*:
2 x Analogue Voltage inputs
• 2 x Analogue Temperature inputs
• 4 x Digital Outputs
*Optional auxiliary harness required to be purchased Haltech Part # HT040003

Functions:
• Dual Bank Closed Loop O2 Control
• Knock Control
• Long Term Fuel Trim
• Over Boost
• Rev Limiter
• Closed & Open Loop Boost Control
• Gear Setup
• ACF On Base Tables
• Transient Throttle Enhance
• Decel Cut

Correction Tables:  Fuel  Ignition  Boost:
• Cranking
• Air Temp Target Correction
• Zero Throttle Gear Correction
• Cylinder Trim
• TPS Correction
• Generic Correction 1
• Generic Correction 2
• Gear Correction
• Post Start
• Air Temp Duty Correction
• Post Start

Miscellaneous:
• Data Logging: 448Kb of onboard data logging, Storage for approx 40 minutes at 10 logs per seconds,
6 channels of data
• Max 20 channels logging capability
• Tune can be password protected in software
• Rugged anodized aluminum casing

Power Requirements:
Source: 8.6 to 16.5 Volts DC
Consumption: 530mA @ 12Volts DC

Physical Dimensions:
ECU Dimensions Length: 154mm (174mm with MAP nipple)
Width: 158mm Height: 42mm Weight: 680g (1.5 lb)

Applications:
Nissan 300ZX (Z32)
Engine Codes:
VG30 , VG30DETT

Transmission:
Manual only (Automatic not supported)

The Kit includes:
Pro Plug-in ECU, USB Cable, Programming Software CD, Quick Start Guide, Instruction Manual (on CD)

Der er endnu ikke nogen anmeldelser her. Vi vil være glade for hvis du vil anmelde som den første.

Tilføj anmeldelse:
spacer