Platinum PRO Plug-in - Hyundai BK Theta Genesis Kit
- Direct plug and play replacement of the OEM ECU, no rewiring necessary
- Uses the car's factory sensors
- Windows 2000, XP, Vista, Windows 7 & 10 compatible software
- Real-time programming, instant hesitation free adjustment while the engine is running
- Fully user definable 32 x 32 mapping
- Tuning via Volumetric Efficiency (VE), Injection time or Lambda Correction (MAF)
- Selectable onboard internal MAP sensor rated to 150kPa (up to 1.5 Bar or 22psi boost)
- Wideband “auto-tuning†using user definable target AFR table
Supported Models:
Hyundai Genesis Coupe (BK) - USA Delivered Model Only
Engine Codes: Theta (2.0T) Only, Manual Transmission Only
Features:
• Direct plug and play replacement of the OEM ECU, No re-wiring necessary
• Uses the vehicles standard sensors & engine hardware
• Electronic Throttle Control - (Drive By Wire) with Cruise Control
• Retains instrument panel functionality via CAN communications
• Windows 2000, XP, Vista, Windows 7 compatible software
• Real time programming, instant hesitation free adjustment while engine is running
• Fully user definable 32 x 32 mapping with over 30 correction tables available
• Tuning via Volumetric Efficiency (VE) or Injection time
• OBDII Diagnostic Trouble Code Storing & Check Engine Light Control – Generic OBDII protocol Only
• Wideband “auto tuning” using user definable target AFR table
• USB and CAN Communication Port
Factory Outputs:
• 4 x Fuel Injector outputs (Peak & Hold)
• 4 x Ignition outputs (15A Internal)
• Electronic Throttle Control (DBW)
• AC Clutch Relay
• Check Engine Light
• Fuel Pump
• Thermo Fan Outputs Cruise Control
• Factory Inputs: MAP sensors Throttle Position Sensor Knock Detection Sensor
• Narrow Band Oxygen sensor
• Coolant Temperature sensor
• Vehicle Speed Sensor
• Air Temperature sensor Power Steering Switch Oil Temperature Sensor
• Brake Switch Clutch Switch
• Expansion I/O: 4 x Analogue Voltage Inputs, 1 x Digital Input, 4 x Digital Outputs
• Configurable for: Aux Rev Limiter Exhaust Gas Temperature Sensors Air Temperature Switch
• Flat Shift Fuel Temperature Sensors
• Aux Fuel Pump
• NOS Enable Oil Temperature Sensors
• Boost Control
• Fuel Pressure Sensor
• Diff Temperature Sensor
• Battery Light
• External Map Sensor (Up to 5 Bar)
• Gearbox Temperature Sensor
• Generic Duty Output
• Oil Pressure Sensor
• Generic Temperature Sensors
• Nitrous Activation Switch
• Wideband O2 Sensors
• Discrete ON/OFF Switches
• Flex Fuel Sensor
Plus much more …
Expansions I/O:
Up to 36 more I/O channels are available using the optional Haltech I/O 12 and TCA 2/4 CAN Devices -
Functions:
• Closed Loop O2 Control
• Knock Control
• Long Term Fuel Trim
• Rev Limiter
• Closed/Open Loop Boost Control
• Gear Setup
• Nitrous Activation Output
• Over Boost protection
• Fuel Composition (E85/Flex Fuel)
• Speed Limiter
• Antilag Launch
• Decel Cut
Correction Tables:
• Fuel Ignition Boost
• Air Temperature Correction
• Air Temp Duty Correction
• Coolant Temperature Correction
• Map Correction
• Zero Throttle Gear Correction
• Cylinder Trim TPS Correction
• Generic Correction
• Gear Correction
Miscellaneous: Data Logging:
• 448Kb of onboard data logging, Storage for approx 40 minutes at 10 logs per seconds, 6 channels of data
• Max 20 channels logging capability
• Tune can be password protected in software
• Rugged anodized aluminum casing
Factory Functions:
• Not Supported: Immobilizer Traction Control
Power Requirements:
• Source: 8.6 to 16.5 Volts DC
• Consumption: 530mA @ 12Volts DC
Operating Temperature Range:
-40Deg C to 85 Deg C ( -40 Deg F to 185 Deg F)
Physical Specifications:
Length: 179mm, Width: 158mm, Height: 42mm, Weight: 730g (1.6 lb)
The kit includes:
Platinum Pro Plug-in Pro Plug-in ECU, USB Cable, Programming Software CD, Quick Start Guide, Instruction Manual (on CD)
Der er endnu ikke nogen anmeldelser her. Vi vil være glade for hvis du vil anmelde som den første.
